吸附物式低溫干燥機

◆服務優缺點 Product features

※包括安穩同一的吸氣壓為和露點

1.活性炭吸附塔之高強度與直經經實驗報告結果顯示細密換算，塔床內壓小，可以保障了再壓縮混合氣體烘干劑5秒的遇到時段，擁有原材料氣的露點的要求。

2.30％的低溫干熱處理劑容量，應用在補償金低溫干熱處理劑的自然的脆化，確保低溫干熱處理。

3.超大吸附器，加強組織領導氣體流動粗糙經由空氣干燥劑層，消失溝流現像。

※回收利用氣量消耗超過14％

1.好的機筒設汁，導出100％的物理吸附糖份，店鋪的糖份廣泛用于增大二次利用關鍵期的二次利用氣體溫，加強設施設備的解吸能力素質，使人二次利用更根除。

2.冷空氣干燥和回收利用用交叉平衡方案范文，濕冷空氣流走干的過濾劑時效性果更佳。回收利用氣出口貿易含濕量調控在亞供大于求感覺，使排氣口消聲器器及排氣口入口通道無結水之慮。

3.可會按照晾干機的正常運行過載供需調高再造能力氣用藥量，確定再造能力氣體間斷平穩，再造能力負荷低至臨界狀態。

※烘干劑運行時間長

1.適合自己的機筒長寬比，使氣體在空氣干躁劑層的空氣流速和日期始終維持好的情況下，做好產生空氣干躁劑的能力。

2.合理安排的體統手機配置，在氣體流動開始機筒前，經除油辦理即時清空氣體流動中內油份物與重被污染的源物，以免 空氣干燥劑層受被污染的源。

※儀器按照了刺激高品味電動及氣動平衡閥和靠得住的全電子廠可c語言編程序把控好器，人機對戰畫質和睦，智能間斷體現 雙塔工作，反復的時間是場所可編，生產日期控制10min。閘閥使用時間歷時50萬次工作。

※鍋筒罐壁作冷熱鍍鋅防水外理，10年不生銹腐蝕現象。

※運作準確的、能力動態平衡、運營簡單便捷，重新安裝不能不的基礎。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆重點技術設備性能參數 Main technical parameters